| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: alb: re-check primary_is_promisc under RTNL in bond_alb_monitor
bond_alb_monitor() reads primary_is_promisc under RCU, then drops RCU and
takes RTNL via rtnl_trylock() before undoing the promiscuity it set on the
active slave. In that window the active slave can change under RTNL
(RTM_DELLINK -> __bond_release_one() -> bond_alb_handle_active_change()),
which already drops the promiscuity and clears primary_is_promisc. The
monitor still acts on the stale decision: if the slave was removed with no
failover, curr_active_slave is now NULL and the deref faults; if it failed
over, the stale dev_set_promiscuity(-1) underflows the new slave's
promiscuity counter and pins it in IFF_PROMISC.
Oops: general protection fault, probably for non-canonical address ...
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
Workqueue: b42 bond_alb_monitor
RIP: 0010:bond_alb_monitor (drivers/net/bonding/bond_alb.c:1600)
process_one_work (kernel/workqueue.c:3322)
worker_thread (kernel/workqueue.c:3486)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
Kernel panic - not syncing: Fatal exception
Re-check primary_is_promisc (and curr_active_slave) after taking RTNL so
the monitor only undoes an increment it still owns. The other bonding
monitors already re-read state under RTNL in their commit phase
(bond_miimon_commit/bond_ab_arp_commit); bond_alb_monitor() was the only
one acting on the pre-trylock decision. |
| In the Linux kernel, the following vulnerability has been resolved:
qede: sync udp_tunnel ports outside qede_lock in the recovery path
A TX timeout on a qede NIC that has VXLAN/GENEVE tunnel ports
configured wedges the rtnetlink control plane of the whole machine:
NETDEV WATCHDOG: ens6f1 (qede): transmit queue 2 timed out 10226 ms
[qede_tx_timeout:586(ens6f1)]TX timeout on queue 2!
[qede_recovery_handler:2665(ens6f0)]Starting a recovery process
The recovery path deadlocks on the driver's own mutex:
qede_sp_task
rtnl_lock()
mutex_lock(&edev->qede_lock) <- taken
qede_recovery_handler
qede_load
udp_tunnel_nic_reset_ntf
__udp_tunnel_nic_device_sync
info->sync_table == qede_udp_tunnel_sync
mutex_lock(&edev->qede_lock) <- same task: deadlock
The mutex is not recursive, so the kworker blocks on itself with
rtnl_lock held, and neither lock is ever released. Every task that
calls rtnl_lock() afterwards (ip, ovs-vswitchd, lldpad, IPv6
addrconf, sshd) blocks forever while the node still answers ping.
In a vmcore from an affected production node rtnl_mutex.owner
decodes to the very kworker blocked at the innermost mutex_lock()
above.
Re-sync the tunnel ports from qede_sp_task() after the internal lock
is dropped, still under rtnl_lock as the udp_tunnel API requires.
This mirrors qede_open(), which calls udp_tunnel_nic_reset_ntf()
under rtnl without the internal lock.
qede_recovery_handler() now returns whether it has successfully
reloaded an open device, and the caller re-syncs the ports only in
that case. This keeps the old gating exactly: a device that was down
or a failed recovery returns false, as those paths never reached the
udp_tunnel_nic_reset_ntf() call before either.
This was the only user of the qede_lock()/qede_unlock() helpers, so
remove them. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vc4: Zero the tile state data array before each BIN job
The binner BO is a single 16MB buffer split into 512KB slots that are
handed out to jobs at submission time and recycled as jobs complete,
without ever being cleared. Each slot holds the job's Tile State Data
Array (TSDA) at its start, followed by the tile allocation pool.
While the tile allocation pool is only walked by the render thread
through branches the binner generated during the current job, the
TSDA is the PTB's own per-tile bookkeeping and is consumed by the
hardware itself. Although the kernel sets the "Auto-initialise Tile
State Data Array" flag in the tile binning mode configuration, the
PTB demonstrably still acts on stale tile state left by the slot's
previous user: the binner ends up creating invalid command streams
with invalid primitive streams and branches, which can cause GPU hangs
as observed in [1][2].
Zero the TSDA when the job's binning slot is configured. This clears
48 bytes per tile (~24KB for a 1080p frame) in the submission path, and
guarantees the PTB never sees another job's tile state.
The tile count is only checked for being non-zero today, so the 8-bit
fields it comes from can describe a tile state array almost six times
larger than the slot it has to live in. Bound it before the slot is
handed out, since such size decides how much of the slot is left for
the tile alloc pool. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: addrconf: bail out of dad_failure when state is no longer POSTDAD
addrconf_dad_failure() transitions ifp->state from DAD to POSTDAD
via addrconf_dad_end(), which drops ifp->lock on return. The lock
is re-acquired after net_info_ratelimited(). A concurrent
ipv6_del_addr() can take the lock in that window, set ifp->state
to DEAD and run list_del_rcu(&ifp->if_list).
addrconf_dad_failure() then overwrites DEAD with ERRDAD at errdad:
and schedules a new dad_work. The work calls ipv6_del_addr()
again, hitting the already-poisoned list entry:
general protection fault: 0000 [#1] SMP NOPTI
CPU: 4 PID: 217 Comm: kworker/4:1
Workqueue: ipv6_addrconf addrconf_dad_work
RIP: 0010:ipv6_del_addr+0xe9/0x280
RAX: dead000000000122
Call Trace:
addrconf_dad_stop+0x113/0x140
addrconf_dad_work+0x28c/0x430
process_one_work+0x1eb/0x3b0
worker_thread+0x4d/0x400
kthread+0x104/0x140
ret_from_fork+0x35/0x40
Fold the addrconf_dad_end() logic into addrconf_dad_failure() under
a single ifp->lock critical section. The STABLE_PRIVACY branch
temporarily drops ifp->lock around address regeneration, so at
lock_errdad: verify the state is still POSTDAD before transitioning
to ERRDAD; bail out otherwise to avoid overwriting a state set by
another path while the lock was released. |
| In the Linux kernel, the following vulnerability has been resolved:
configfs: fix lockless traversals of ->s_children
Having the parent directory locked protects entries from removal
by another thread, but it does *not* protect cursors from being
moved around by lseek() - or freed, for that matter. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: clear sock_ops cb flags before force-closing a child socket
A child socket inherits the listener's bpf_sock_ops_cb_flags via
sk_clone_lock(). If its setup fails in tcp_v4_syn_recv_sock() /
tcp_v6_syn_recv_sock(), the child is freed through put_and_exit, where
inet_csk_prepare_forced_close() drops the socket lock and tcp_done() runs
without it.
If BPF_SOCK_OPS_STATE_CB_FLAG was inherited, tcp_done() -> tcp_set_state()
calls tcp_call_bpf(), which expects the lock and trips sock_owned_by_me():
WARNING: include/net/sock.h:1799 at tcp_set_state+0x433/0x550
RIP: 0010:tcp_set_state+0x433/0x550 include/net/sock.h:1799
Call Trace:
<IRQ>
tcp_done+0xba/0x250 net/ipv4/tcp.c:5095
tcp_v4_syn_recv_sock+0x850/0xa50 net/ipv4/tcp_ipv4.c:1787
tcp_check_req+0xf30/0x1360 net/ipv4/tcp_minisocks.c:926
tcp_v4_rcv+0x1047/0x1b50 net/ipv4/tcp_ipv4.c:2164
</IRQ>
The child is freed before it is ever established, so it should run no
sock_ops callback. Clear its cb flags in inet_csk_prepare_for_destroy_sock(),
the common point for the IPv4, IPv6 and chtls forced-close paths and for the
MPTCP ->syn_recv_sock() failure path (dispose_child), which reaches tcp_done()
on a child that was never established too. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ipset: make sure gc is properly stopped
Sashiko noticed that when destroying a set,
cancel_delayed_work_sync() was called while gc
calls queue_delayed_work() unconditionally which
can lead not to properly shutting down the gc. |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: wait for in-flight TLS handshake callback when cancel loses race
When wait_for_completion_interruptible_timeout() in
svc_tcp_handshake() returns 0 (timeout) or -ERESTARTSYS (signal) and
tls_handshake_cancel() then returns false, handshake_complete() has
won the cancellation race: it has set HANDSHAKE_F_REQ_COMPLETED and
is about to invoke svc_tcp_handshake_done(), but the callback's
side effects on xpt_flags and on svsk->sk_handshake_done have not
yet committed.
The current code reads xpt_flags immediately to decide whether the
session succeeded. Two races result.
If the callback has executed set_bit(XPT_TLS_SESSION) but not yet
clear_bit(XPT_HANDSHAKE), svc_tcp_handshake() sees a session,
enqueues the transport, and returns. svc_xprt_received() then
clears XPT_BUSY, a worker thread picks the transport up, the
dispatcher in svc_handle_xprt() observes XPT_HANDSHAKE still set,
and xpo_handshake is invoked a second time. That svc_tcp_handshake()
calls init_completion(&svsk->sk_handshake_done) while the original
callback concurrently calls complete_all() on it, corrupting the
embedded swait_queue.
If the callback has set HANDSHAKE_F_REQ_COMPLETED but not yet
entered svc_tcp_handshake_done(), svc_tcp_handshake() reads
XPT_TLS_SESSION as clear and tears the connection down even though
the handshake is about to succeed.
Wait for the callback to commit before inspecting xpt_flags. The
completion is guaranteed to fire because handshake_complete()
invokes svc_tcp_handshake_done() unconditionally once it has set
HANDSHAKE_F_REQ_COMPLETED. |
| Concurrent execution using shared resource with improper synchronization ('race condition') in Windows Installer allows an authorized attacker to elevate privileges locally. |
| Improper Verification of Cryptographic Signature vulnerability in Apache CXF's JAX-RS XML Security module. The JAX-RS XML Signature interceptors (XmlSigInHandler, XmlSigInInterceptor and the streaming XmlSecInInterceptor) did not ensure that the XML passed to the application was covered by the signature. An attacker with any document signed by a trusted key could wrap it in unsigned content, which the application would then treat as signed.
Users are recommended to upgrade to versions 4.2.4 or 4.1.9 or 3.6.13, which fix this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
audit: Fix data races of skb_queue_len() readers on audit_queue
Multiple readers access audit_queue.qlen via skb_queue_len() without
holding the queue lock or using READ_ONCE(), while kauditd writes to
this field via the skb_dequeue() → __skb_unlink() path with WRITE_ONCE()
protected by a spinlock. This constitutes data races.
All affected skb_queue_len(&audit_queue) call sites:
- kauditd_thread() wait_event_freezable() condition
- audit_receive_msg() AUDIT_GET handler (s.backlog assignment)
- audit_receive() backlog check
- audit_log_start() backlog check and pr_warn()
KCSAN reports the following conflicting access pattern (one example):
==================================================================
BUG: KCSAN: data-race in audit_log_start / skb_dequeue
write (marked) to 0xffffffff8512ee20 of 4 bytes by task 661 on cpu 57:
skb_dequeue+0x70/0xf0
kauditd_send_queue+0x71/0x220
kauditd_thread+0x1cb/0x430
kthread+0x1c2/0x210
ret_from_fork+0x162/0x1a0
ret_from_fork_asm+0x1a/0x30
read to 0xffffffff8512ee20 of 4 bytes by task 36586 on cpu 1:
audit_log_start+0x2a0/0x6b0
audit_core_dumps+0x64/0xa0
do_coredump+0x14b/0x1260
get_signal+0xeb2/0xf70
arch_do_signal_or_restart+0x41/0x170
exit_to_user_mode_loop+0xa2/0x1c0
do_syscall_64+0x1a3/0x1c0
entry_SYSCALL_64_after_hwframe+0x76/0xe0
value changed: 0x00000001 -> 0x00000000
==================================================================
Resolve the race by switching to lockless helper skb_queue_len_lockless(),
which internally uses READ_ONCE() and properly pairs with the WRITE_ONCE()
write accesses already present on the writer side.
[PM: line length tweak] |
| In the Linux kernel, the following vulnerability has been resolved:
writeback: fix race between cgroup_writeback_umount() and inode_switch_wbs()
When a container exits, the following BUG_ON() is occasionally triggered:
==================================================================
VFS: Busy inodes after unmount of sdb (ext4)
------------[ cut here ]------------
kernel BUG at fs/super.c:695!
CPU: 3 PID: 6 Comm: containerd-shim Tainted: G OE K 6.6 #1
pstate: 63400009 (nZCv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--)
pc : generic_shutdown_super+0xf0/0x100
lr : generic_shutdown_super+0xf0/0x100
Call trace:
generic_shutdown_super+0xf0/0x100
kill_block_super+0x20/0x48
ext4_kill_sb+0x28/0x60
deactivate_locked_super+0x54/0x130
deactivate_super+0x84/0xa0
cleanup_mnt+0xa4/0x140
__cleanup_mnt+0x18/0x28
task_work_run+0x78/0xe0
do_notify_resume+0x204/0x240
==================================================================
The root cause is a race between cgroup_writeback_umount() and
inode_switch_wbs()/cleanup_offline_cgwb(). There is a window between
inode_prepare_wbs_switch() returning true and the subsequent
wb_queue_isw() call. Following is the process that triggers the issue:
CPU A (umount) | CPU B (writeback)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
inode_switch_wbs/cleanup_offline_cgwb
atomic_inc(&isw_nr_in_flight)
inode_prepare_wbs_switch
-> passes SB_ACTIVE check
__iget(inode)
generic_shutdown_super
sb->s_flags &= ~SB_ACTIVE
cgroup_writeback_umount(sb)
smp_mb()
atomic_read(&isw_nr_in_flight)
rcu_barrier()
-> no pending RCU callbacks
flush_workqueue(isw_wq)
-> nothing queued, returns
evict_inodes(sb)
-> Inode skipped as isw still holds a ref.
sop->put_super(sb)
/* destroys percpu counters */
-> VFS: Busy inodes after unmount!
wb_queue_isw()
queue_work(isw_wq, ...)
/* later in work function */
inode_switch_wbs_work_fn
process_inode_switch_wbs
iput() -> evict
percpu_counter_dec() // UAF!
Fix this by extending the RCU read-side critical section in
inode_switch_wbs() and cleanup_offline_cgwb() to cover from
inode_prepare_wbs_switch() through wb_queue_isw(). Since there is
no sleep in this window, rcu_read_lock() can be used. Then add a
synchronize_rcu() in cgroup_writeback_umount() before the existing
rcu_barrier(), so that all in-flight switchers that have passed the
SB_ACTIVE check have completed queue_work() before flush_workqueue()
is called.
The existing rcu_barrier() is intentionally retained so this fix can
be backported unchanged to stable kernels (5.10.y, 6.6.y, ...) that
still queue switches via queue_rcu_work(). It is a no-op on current
mainline (since commit e1b849cfa6b6 ("writeback: Avoid contention on
wb->list_lock when switching inodes")) and is removed in a follow-up
patch. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: core: fix adapter deregistration race
Adapters can be looked up by their id using i2c_get_adapter() which
takes a reference to the embedded struct device.
Remove the adapter from the IDR before tearing it down during
deregistration (and on registration failure) to make sure its resources
are not accessed after having been freed (e.g. the device name). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ipset: fix race between dump and ip_set_list resize
The release path of ip_set_dump_do() and ip_set_dump_done() read
inst->ip_set_list via ip_set_ref_netlink(), a plain rcu_dereference_raw()
of the array pointer. These run from netlink_recvmsg() without the nfnl
mutex and without an RCU read-side critical section.
A concurrent ip_set_create() can grow the array: it publishes the new
array, calls synchronize_net() and then kvfree()s the old one. Since the
dump paths read the array outside any RCU reader, synchronize_net() does
not wait for them and the old array can be freed while they still index
into it, causing a use-after-free.
The dumped set itself stays pinned via set->ref_netlink, so only the
array load needs protecting. Take rcu_read_lock() around it, matching
ip_set_get_byname() and __ip_set_put_byindex().
BUG: KASAN: slab-use-after-free in ip_set_dump_do (net/netfilter/ipset/ip_set_core.c:1697)
Read of size 8 at addr ffff88800b5c4018 by task exploit/150
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
ip_set_dump_do (net/netfilter/ipset/ip_set_core.c:1697)
netlink_dump (net/netlink/af_netlink.c:2325)
netlink_recvmsg (net/netlink/af_netlink.c:1976)
sock_recvmsg (net/socket.c:1159)
__sys_recvfrom (net/socket.c:2315)
...
Oops: general protection fault, probably for non-canonical address ... KASAN NOPTI
KASAN: maybe wild-memory-access in range [0x02d6...d0-0x02d6...d7]
RIP: 0010:ip_set_dump_do (net/netfilter/ipset/ip_set_core.c:1698)
Kernel panic - not syncing: Fatal exception |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: Serialize UMP output teardown with event_input
seq_ump_process_event() borrows client->out_rfile.output without
synchronizing with the first-open and last-close transition in
seq_ump_client_open() and seq_ump_client_close().
The last output unuse can therefore drop opened[STR_OUT] to zero and
release the rawmidi file while an in-flight event_input callback is still
inside snd_rawmidi_kernel_write(). That leaves the rawmidi substream
runtime exposed to teardown before the write path has taken its own
buffer reference.
Add a per-client rwlock for the event_input-visible output file. Publish
a newly opened output file under the write side, and hold the read side
from the output lookup through snd_rawmidi_kernel_write(). The last
output close copies and clears the visible output file under the write
side, then drops the lock and releases the saved rawmidi file. Use
IRQ-safe rwlock guards because event_input can also be reached from
atomic sequencer delivery.
The buggy scenario involves two paths, with each column showing the
order within that path:
path A label: event_input path path B label: last unuse path
1. seq_ump_process_event() reads 1. seq_ump_client_close()
client->out_rfile.output. drops opened[STR_OUT] to zero.
2. snd_rawmidi_kernel_write1() 2. snd_rawmidi_kernel_release()
has not yet pinned runtime. closes the output file.
3. The writer continues using 3. close_substream() frees
the borrowed substream. substream->runtime.
This keeps the output substream and runtime alive for the full
event_input write while keeping rawmidi release outside the rwlock.
KASAN reproduced this as a slab-use-after-free in
snd_rawmidi_kernel_write1(), with allocation through
seq_ump_use()/snd_seq_port_connect() and free through
seq_ump_unuse()/snd_seq_port_disconnect().
Validation reproduced this kernel report:
KASAN slab-use-after-free in snd_rawmidi_kernel_write1+0x9d/0x400
RIP: 0033:0x7f5528af837f
Read of size 8
Call trace:
dump_stack_lvl+0x73/0xb0 (?:?)
print_report+0xd1/0x650 (?:?)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
__virt_addr_valid+0x1a7/0x340 (?:?)
kasan_complete_mode_report_info+0x64/0x200 (?:?)
kasan_report+0xf7/0x130 (?:?)
snd_rawmidi_kernel_write1+0x9d/0x400 (?:?)
__asan_load8+0x82/0xb0 (?:?)
update_stack_state+0x1ef/0x2d0 (?:?)
snd_rawmidi_kernel_write+0x1a/0x20 (?:?)
seq_ump_process_event+0xd4/0x120 (sound/core/seq/seq_ump_client.c:82)
__snd_seq_deliver_single_event+0x8a/0xe0 (?:?)
snd_seq_deliver_from_ump+0x2b2/0xd60 (?:?)
lock_acquire+0x14e/0x2e0 (?:?)
find_held_lock+0x31/0x90 (?:?)
snd_seq_port_use_ptr+0xa6/0xe0 (?:?)
__kasan_check_write+0x18/0x20 (?:?)
do_raw_read_unlock+0x32/0xa0 (?:?)
_raw_read_unlock+0x26/0x50 (?:?)
snd_seq_deliver_single_event+0x45c/0x4b0 (?:?)
snd_seq_deliver_event+0x10d/0x1b0 (?:?)
snd_seq_client_enqueue_event+0x192/0x240 (?:?)
snd_seq_write+0x2cd/0x450 (?:?)
apparmor_file_permission+0x20/0x30 (?:?)
security_file_permission+0x51/0x60 (?:?)
vfs_write+0x1ce/0x850 (?:?)
__fget_files+0x12b/0x220 (?:?)
lock_release+0xc8/0x2a0 (?:?)
__rcu_read_unlock+0x74/0x2d0 (?:?)
__fget_files+0x135/0x220 (?:?)
ksys_write+0x15a/0x180 (?:?)
rcu_is_watching+0x24/0x60 (?:?)
__x64_sys_write+0x46/0x60 (?:?)
x64_sys_call+0x7d/0x20d0 (?:?)
do_syscall_64+0xc1/0x360 (arch/x86/entry/syscall_64.c:87)
entry_SYSCALL_64_after_hwframe+0x77/0x7f (?:?) |
| In the Linux kernel, the following vulnerability has been resolved:
net: shaper: rework the VALID marking (again)
Recent commit changed the semantics from NOT_VALID to VALID.
I didn't realize that the flags are not stored atomically
with the entry in XArray. There's still a race of reader
observing a VALID mark for a slot, getting interrupted,
writer replacing the entry with a different one, reader
continuing, fetching the entry which is now a different
pointer than the pointer for which VALID was meant.
The biggest consequence of this is that we may see a UAF
since net_shaper_rollback() assumed that entries without
VALID can be freed without observing RCU.
Looks like the XArray marks are buying us nothing at this
point. Let's convert the code to an explicit valid field.
The smp_load_acquire() / smp_store_release() barriers are
marginally cleaner. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, skmsg: fix verdict sk_data_ready racing with ktls rx
sk_psock_strp_data_ready() already checks tls_sw_has_ctx_rx() and
defers to psock->saved_data_ready when a TLS RX context is present,
avoiding a conflict with the TLS strparser's ownership of the receive
queue (commit e91de6afa81c, "bpf: Fix running sk_skb program types
with ktls").
sk_psock_verdict_data_ready() has no equivalent guard. When a socket
is inserted into a sockmap (BPF_SK_SKB_VERDICT) before TLS RX is
configured, tls_sw_strparser_arm() saves sk_psock_verdict_data_ready
as rx_ctx->saved_data_ready. On data arrival:
tls_data_ready -> tls_strp_data_ready -> tls_rx_msg_ready
-> saved_data_ready() = sk_psock_verdict_data_ready()
-> tcp_read_skb() drains sk_receive_queue via __skb_unlink()
without calling tcp_eat_skb(), so copied_seq is not advanced.
tls_strp_msg_load() then finds tcp_inq() >= full_len (stale), calls
tcp_recv_skb() on the now-empty queue, hits WARN_ON_ONCE(!first), and
returns with rx_ctx->strp.anchor.frag_list pointing at a psock-owned
(potentially freed) skb. tls_decrypt_sg() subsequently walks that
frag_list: use-after-free.
Apply the same fix as sk_psock_strp_data_ready(): if a TLS RX context
is present, call psock->saved_data_ready (sock_def_readable) to wake
recv() waiters and return immediately, leaving the receive queue
untouched. TLS retains sole ownership of the queue and decrypts the
record normally through tls_sw_recvmsg(). |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: fix race between sctp_wait_for_connect and peeloff
sctp_wait_for_connect() drops and re-acquires the socket lock while
waiting for the association to reach ESTABLISHED state. During this
window, another thread can peeloff the association to a new socket via
getsockopt(SCTP_SOCKOPT_PEELOFF), changing asoc->base.sk. After
re-acquiring the old socket lock, sctp_wait_for_connect() returns
success without noticing the migration — the caller then accesses
the association under the wrong lock in sctp_datamsg_from_user().
Add the same sk != asoc->base.sk check that sctp_wait_for_sndbuf()
already has, returning an error if the association was migrated while
we slept. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bcmgenet: fix racing timeout handler
The bcmgenet_timeout handler tries to take down all tx queues when
a single queue times out. This is over zealous and causes many race
conditions with queues that are still chugging along. Instead lets
only restart the timed out queue. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_uart: fix UAFs and race conditions in close and init paths
Vulnerabilities leading to Use-After-Free (UAF) and Null Pointer
Dereference (NPD) conditions were observed in the lifecycle management
of hci_uart.
The primary issue arises because the workqueues (init_ready and
write_work) are only flushed/cancelled if the HCI_UART_PROTO_READY
flag is set during TTY close. If a hangup occurs before setup completes,
hci_uart_tty_close() skips the teardown of these workqueues and
proceeds to free the `hu` struct. When the scheduled work executes
later, it blindly dereferences the freed `hu` struct.
Furthermore, several data races and UAFs were identified in the teardown
sequence:
1. Calling hci_uart_flush() from hci_uart_close() without effectively
disabling write_work causes a race condition where both can concurrently
double-free hu->tx_skb. This happens because protocol timers can
concurrently invoke hci_uart_tx_wakeup() and requeue write_work.
2. Calling hci_free_dev(hdev) before hu->proto->close(hu) causes a UAF
when vendor specific protocol close callbacks dereference hu->hdev.
3. In the initialization error paths, failing to take the proto_lock
write lock before clearing PROTO_READY leads to races with active
readers. Additionally, hci_uart_tty_receive() accesses hu->hdev
outside the read lock, leading to UAFs if the initialization error
path frees hdev concurrently.
Fix these synchronization and lifecycle issues by:
1. Re-ordering hci_uart_tty_close() to clear HCI_UART_PROTO_READY first,
followed immediately by a cancel_work_sync(&hu->write_work). Clearing
the flag locks out concurrent protocol timers from successfully invoking
hci_uart_tx_wakeup(), effectively rendering the cancellation permanent
and preventing the tx_skb double-free.
2. Note: Clearing PROTO_READY early causes hci_uart_close() to skip
hu->proto->flush(). This is perfectly safe in the tty_close path
because hu->proto->close() executes shortly after, which intrinsically
purges all protocol SKB queues and tears down the state.
3. Relocating hu->proto->close(hu) strictly prior to hci_free_dev(hdev)
across all close and error paths to prevent vendor-level UAFs.
4. Moving the hdev->stat.byte_rx increment in hci_uart_tty_receive()
inside the proto_lock read-side critical section to safely synchronize
with device unregistration.
5. Adding cancel_work_sync(&hu->write_work) to hci_uart_close() to safely
flush the workqueue before hci_uart_flush() is invoked via the HCI core.
6. Utilizing cancel_work_sync() instead of disable_work_sync() across
all paths to prevent permanently breaking user-space retry capabilities. |
