| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| A malicious actor with access to the network could exploit a Binding to an Unrestricted IP Address vulnerability found in WiFiman Desktop to obtain information about the host device. |
| In the Linux kernel, the following vulnerability has been resolved:
Drivers: hv: Don't reset VMBus connection state on error/exit paths
In two places, current code forces vmbus_connection.conn_state to
DISCONNECTED prior to calling vmbus_disconnect(). But vmbus_disconnect()
calls vmbus_initiate_unload(), which unloads the VMBus connection
only if the conn_state is CONNECTED. Consequently, the connection
remains and the Hyper-V host might continue to send messages or post
VMBus interrupts.
The problem was introduced in commit 74347a99e73ae ("x86/Hyper-V:
Unload vmbus channel in hv panic callback"), in that
vmbus_initiate_unload() started checking the current connection
state before doing the unload. This commit removed some occurrences
where conn_state was forced to DISCONNECTED, but these two remained,
apparently due to an oversight at the time.
Fix this by not forcing conn_state to DISCONNECTED during VMBus exit,
or if a failure occurs when establishing the connection in the first
place. Whatever value conn_state has at the time is then read by
vmbus_initiate_unload() to determine if there is a connection to
be unloaded. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock: treat TCP_CLOSING as once-established
Handle the TCP_ESTABLISHED -> TCP_CLOSING transition on OP_RST, which can
race with the connect loop. Immediately break and return 0 on
ESTABLISHED/CLOSING. The return value of connect() should reflect what
happened up to the point the connection was established or failed. Events
that occur afterwards must not affect it. E.g. even if OP_RW has already
set sk_err, connect() should still return 0, not ENOBUFS because of it.
Adapt the inaccurate comment above signal_pending().
Resetting a socket that is still present in connected_table can lead to
memory corruption. The reporter noted lost transports for in-flight skbs,
and I have reproduced crashes caused by re-insertion into connected_table.
list_add double add: new=, prev=, next=.
kernel BUG at lib/list_debug.c:35!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
Workqueue: vsock-loopback vsock_loopback_work
RIP: 0010:__list_add_valid_or_report+0x11f/0x130
Call Trace:
vsock_insert_connected.cold+0xe/0x13
virtio_transport_recv_pkt+0x10e9/0x1460
vsock_loopback_work+0x305/0x480
process_one_work+0xe4c/0x1560
worker_thread+0x4f1/0xd60
kthread+0x36e/0x470
ret_from_fork+0x47b/0x6b0
ret_from_fork_asm+0x1a/0x30
This fix is supplementary to commit 002541ef650b ("vsock: Ignore
signal/timeout on connect() if already established"). Details under Link. |
| In the Linux kernel, the following vulnerability has been resolved:
net/rds: don't let the rdma_cm destroy an id RDS still owns on route failure
rds_rdma_cm_event_handler_cmn() hands the return value of
rdma_resolve_route() straight back to the rdma_cm on
RDMA_CM_EVENT_ADDR_RESOLVED. A synchronous failure there - -ENOMEM
from the route work allocation, an SA query that cannot be set up, a
RoCE route with no usable device - makes addr_handler() destroy the
id the event was delivered on. That id is ic->i_cm_id, and nothing
clears the pointer: the connection sits in RDS_CONN_CONNECTING with a
freed id until its shutdown calls rdma_disconnect() and
rdma_destroy_id() on it.
The ROUTE_RESOLVED case already avoids this: rds_ib_cm_initiate_connect()
forces a zero return while ic->i_cm_id == cm_id, as the comment there
explains. Do the same here - drop the connection and return 0 - so
the id stays RDS's to destroy from the shutdown, and the reconnect
gets a fresh one. |
| In the Linux kernel, the following vulnerability has been resolved:
pipe: preserve existing fasync readers on writer setup failure
F_SETFL and FIOASYNC decide whether to invoke ->fasync() before
pipe_fasync() takes pipe->mutex. Two enables of one O_RDWR FIFO can
therefore both enter the callback.
fasync_helper() allocates before checking for an existing entry. If the
first enable installs both entries, a second enable can update the
reader entry and then fail the allocation for the writer entry. The
error path removes the pre-existing reader entry, clearing FASYNC while
the writer entry remains registered. __fput() then skips ->fasync(), so a
later pipe notification can dereference the freed file or its f_owner.
An unprivileged memory-pressure reproducer triggers a KASAN
slab-use-after-free in send_sigio() through this path.
Keep the reader helper's result and undo the registration only if this
call added it. The pipe mutex serializes changes to both lists, so a
failed new registration still removes its reader, while a failed
duplicate preserves the existing registrations and FASYNC. Successful
duplicate enables continue to update fa_fd as before. |
| In the Linux kernel, the following vulnerability has been resolved:
eventfs: Free the eventfs_inode after an rcu grace period too
tracefs_d_revalidate() reads ->is_freed of the eventfs_inode that
dentry->d_fsdata points to, and ->d_revalidate() is called in rcu
pathwalk mode with nothing but rcu_read_lock() held. The dentry itself
stays around for such a walker, but tracefs_d_release() drops its
reference to the eventfs_inode when the dentry is killed, and
release_ei() then frees it after a grace period of eventfs_srcu. An
SRCU grace period doesn't wait for rcu_read_lock() sections, so the
walker can read an eventfs_inode that is already gone.
With a pathwalk held up in tracefs_d_revalidate() while the dentry goes
away:
BUG: KASAN: slab-use-after-free in tracefs_d_revalidate+0x76/0x90
Read of size 1 at addr ff1100010152d8d0 by task walker/97
Call Trace:
<TASK>
tracefs_d_revalidate+0x76/0x90
lookup_fast+0x320/0x640
path_lookupat+0x160/0xb00
filename_lookup+0x1f1/0x5b0
vfs_statx+0xd7/0x3b0
vfs_fstatat+0x4d/0x90
__do_sys_newfstatat+0xa0/0x100
do_syscall_64+0x10e/0x5e0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
[...]
Allocated by task 1:
__kmalloc_cache_noprof+0x249/0x560
eventfs_create_dir+0x7a/0x590
event_create_dir+0x2fb/0xcf0
trace_add_event_call+0xbf/0x150
[...]
Freed by task 11:
kfree+0x1db/0x5b0
srcu_invoke_callbacks+0x3a3/0x620
process_one_work+0x937/0x1810
worker_thread+0x4f1/0xd60
Before commit 8e556432477e ("eventfs: Use SRCU for freeing
eventfs_inodes") release_ei() used call_rcu(), which covered the walker,
while eventfs_iterate() needs the SRCU grace period. Wait for both and
chain call_rcu() from the SRCU callback. |
| In the Linux kernel, the following vulnerability has been resolved:
namespace: a mount that copy_tree() leaves out can't take over a lock
Since commit c62a4766937e ("move_mount: transfer MNT_LOCKED") a mount
can be moved beneath a locked mount. The lock moves from the old cover
to the new mount which takes over the job of hiding what's under it and
the old cover can be unmounted. That works as long as the new mount
stays. But the caller picks the new mount and copy_tree() leaves a
mount of a mount namespace file out of every copy made without
CL_COPY_MNT_NS_FILE, together with everything mounted on it, and never
looks at MNT_LOCKED. unshare(CLONE_NEWNS) and mount propagation make
such copies.
So a task that is root in its own user namespace gets rid of a locked
cover on a file without a race and without touching the filesystem
below it. It makes a child with a mount namespace of its own, binds the
child's /proc/<pid>/ns/mnt beneath the cover with MOVE_MOUNT_BENEATH,
which hands the lock to that bind, and calls unshare(CLONE_NEWNS). The
new mount namespace has nothing on the file. That's the usual way to
mask a single file, a bind of /dev/null or of an empty file. With a
bind of an ordinary file the file stays covered.
copy_tree() already refuses to leave out a locked unbindable mount with
-EPERM since commit df7342b24018 ("mount: Don't allow copying
MNT_UNBINDABLE|MNT_LOCKED mounts"). Do the same for a locked mount of a
mount namespace file. That also covers a tree copied with
CL_COPY_MNT_NS_FILE and attached into a mount namespace of another user
namespace where lock_mnt_tree() locks it. Note that unshare(CLONE_NEWNS)
and clone(CLONE_NEWNS) fail with EPERM from such a mount namespace from
then on. The mount can't be left out and it can't be unmounted.
And refuse to move a mount of a mount namespace file beneath a locked
mount in the first place. Otherwise the task ends up with a mount it
can't unmount and an unshare() that fails for good.
Chris also found a second mount that goes away by itself, a clone of an
automounted mount that shrink_submounts() took along with its parent.
Commit f78ddcc87224 ("namespace: never expire a locked mount") took
care of that one.
Chris's reproducer is appended. Mode nsfile reads SECRET after the
unshare() on 7.3-rc7, with this patch the move_mount() fails with
EINVAL and the file stays covered. nsfile-control uses an ordinary file
and reads MASK both ways.
// SPDX-License-Identifier: GPL-2.0
/*
* Get rid of a locked cover with MOVE_MOUNT_BENEATH.
*
* The "admin" (root) makes a tmpfs W:
* W/D file, holds SECRET, covered by a bind of a file with MASK
* W/Dd/inner file, holds SECRET, Dd is covered by a bind of a directory
* whose "inner" holds MASK
* W/own directory of uid 1000 with the file "mine" and the
* directory "minedir", whose "inner" holds MINE
* W/dbg debugfs, mode 755. dbg/tracing is an automount point
* The "attacker" is uid 1000. It enters a new user namespace with a new mount
* namespace, so W and both covers are locked there.
*
* usage: prog MODE
* plain put a bind of own/mine beneath the cover of D, unmount the cover
* nsfile put a bind of the mount namespace file of a child beneath the
* cover of D, then unshare(CLONE_NEWNS)
* nsfile-control the same with a bind of own/mine
* shrink put a bind of the automounted tracefs beneath the cover of Dd,
* unmount the cover, put a tmpfs beneath W, call umount(W), which fails
* shrink-control the same with a bind of own/minedir
* The environment variable AUTOMOUNT_DIR names another automount point for "shrink".
*/
#define _GNU_SOURCE
#include <errno.h>
#include <fcntl.h>
#include <grp.h>
#include <sched.h>
#include <signal.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <unistd.h>
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: keep the eviction fence until the last handle is closed
amdgpu_gem_object_close() detaches the user queue eviction fence from
the BO before it checks bo_va->ref_count, so closing any handle of a BO
removes the fence, even when the file still has another handle to the
BO and the bo_va with its GPU mappings stays. The BO can then be evicted
without suspending the user queues of the file, which keep accessing it
through mappings that are only marked for update.
Seen on navi31 with a SDMA user queue: a BO opened twice in the same
file (GEM_FLINK + GEM_OPEN) loses its eviction fence when the second
handle is closed (traced attach/detach of the fence):
attach bo=ffff8c78a6c84c00
GEM_CLOSE handle=7
detach bo=ffff8c78a6c84c00
while handle 6 and the mapping are still in use.
Only detach the fence when the last reference to the bo_va goes away,
matching amdgpu_gem_object_open(), which attaches it only when the
bo_va is created. With this the fence stays until the file is closed.
(cherry picked from commit 8387982f03d4026b7dc11b0b5e3118298eee4d6a) |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Check operator stack capacity before pushing
predicate_parse() uses the first operator stack entry before processing
any opening parentheses. A push then increments top before writing.
The existing check still permits that write when top already points to
the last allocated entry, which can access beyond the operator stack.
Reject the push when top reaches the last allocated entry. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-crypt: fix a tiny race condition in crypt_dec_pending
crypt_dec_pending reads io->error before calling atomic_dec_and_test.
Another context, for example crypt_endio called from an interrupt, may
set io->error and drop its reference between the read and the
decrement. crypt_dec_pending then drops the last reference and completes
the bio with the stale status - so a read that failed and was never
decrypted, or a write that failed, is reported as successful.
The read was placed before the decrement by commit b35f8caa0890 ("dm
crypt: wait for endio to complete before destruction"), because that
commit freed dm_crypt_io before calling bio_endio. This is no longer the
case, dm_crypt_io lives in the per-bio data now.
Read io->error after atomic_dec_and_test instead. atomic_dec_and_test is
fully ordered, so no additional barrier is needed. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: fix capability check in xfs
An user reported a bug where he managed to evade group's quota
by changing a file's gid to a different group id the same user
belonged to, even though quotas were enforced on both gids and the
file's size was big enough to exceed the quota's hardlimit.
Commit eba0549bc7d1 replaced a capable() call by a
has_capability_noaudit() to prevent unnecessary selinux audit messages.
Turns out that both calls have slightly different semantics even though
their documentation seems similar. Where in a nutshell:
capable() - Tests the task's effective credentials
has_ns_capability_noaudit() - Tests the task's real credentials
This most of the time has no practical difference but in some cases like
changing attrs (specifically group id in this case) through a NFS client
this will allow the quota code to use XFS_QMOPT_FORCE_RES, effectively
bypassing quota accounting checks.
Using instead ns_capable_noaudit() should fix this issue and prevent
selinux audit messages.
This also fix the remaining calls to has_capability_noaudit() |
| In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: validate packet source for connected sockets
virtio_transport_recv_pkt() looks up sockets first by the full source and
destination tuple, then by destination only in the bound table. The
fallback is needed for listening and connecting sockets, but sockets remain
in the bound table after connect(), so it can also return a non-listening
socket.
The fallback does not validate the source address. In TCP_SYN_SENT, a
RESPONSE from an unrelated source can transition the victim socket to
TCP_ESTABLISHED while its stored remote address remains unchanged.
Subsequent RW packets from that source are delivered through the same
destination-only fallback.
This was reproduced with capability-empty processes under different UIDs.
The attacker discovered the target tuple through unprivileged AF_VSOCK
sock_diag and caused the victim socket to read 16 attacker-chosen bytes;
the intended peer-side socket read 0 of those 16 bytes.
Add vsock_check_source() to validate the transport, source port and source
CID against the peer stored in a non-listening socket. The local transport
is the CID exception because its packets are generated internally with
VMADDR_CID_LOCAL as their source, including connections using CID aliases.
Use the helper after lock_sock() in the virtio receive path. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: mcast: don't truncate the port group walk on teardown
__br_multicast_disable_port_ctx() and br_multicast_del_port() walk
port->mglist with hlist_for_each_entry_safe(). However,
br_multicast_find_del_pg() can also delete other entries from the same
list through br_multicast_fwd_src_remove() or __fwd_del_star_excl().
If such an entry is the iterator's saved next node, hlist_del_init()
clears its ->next and terminates the walk early. The reproducer triggers
this in both teardown walks, leaving port groups in the bridge mdb with
a dangling ->key.port after del_nbp() frees the port:
BUG: KASAN: slab-use-after-free in __mdb_fill_info+0x1191/0x1320
__mdb_fill_info+0x1191/0x1320
br_mdb_dump+0x594/0xe40
rtnl_mdb_dump+0x1cf/0x5d0
Use hlist_del_init_rcu() to unlink the group while preserving ->next.
br_multicast_del_pg() and the teardown walks run under
br->multicast_lock. The GC worker must acquire the same lock before
detaching the group for destruction, so the node remains alive while
the walk uses the preserved pointer.
Preserving ->next means a walk can now reach a group that an earlier
iteration already deleted as a side effect. That group is off mp->ports,
so br_multicast_find_del_pg() would fall through its port scan and hit
the trailing WARN_ON(1). Skip such groups at the top of that helper: a
port group is put on port->mglist when it is created and only unlinked
when it is deleted, so hlist_unhashed() identifies exactly this case. |
| In the Linux kernel, the following vulnerability has been resolved:
net: psp: do not inherit the Rx association on clone
sk->psp_assoc sits past sk_dontcopy_end, so sock_copy() copies it into
every socket accepted from a listener without taking a reference, while
inet_sock_destruct() puts for every inet socket. psp_twsk_init() does
refcount_inc() for the timewait socket, so a child closing through
TIME_WAIT cancels its own put and leaves the association with one
reference and N timewait sockets holding the same pointer. Closing the
listener frees it, and the timewait timers then put freed memory.
Rejecting the association on a listening socket is not sufficient: a socket
can acquire one while established and then be turned back into a listener,
because tcp_disconnect() leaves sk->psp_assoc in place.
BUG: KASAN: slab-use-after-free in psp_twsk_assoc_free+0x6f/0xf0
Write of size 4 at addr ffff888110f9255c by task swapper/7/0
psp_twsk_assoc_free+0x6f/0xf0
inet_twsk_put+0xda/0x1b0
call_timer_fn+0x53/0x2e0
__run_timers+0x764/0xa80
Freed by task 99:
kfree+0x1a7/0x500
process_one_work+0x7ec/0x1100
An association carries a per-connection SPI and key, so a child must not
inherit the parent's. Clear it on clone. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: cls_flower: validate mask pointer after nla_next()
fl_set_enc_opt() iterates the key's nested tunnel-option attributes
with nla_for_each_attr() while advancing a single mask pointer via
nla_next() at the bottom of each loop, so the mask cursor is driven
by the number of key attributes rather than by the mask's own
attributes. The nla_ok() added by commit c96adff956191 ("cls_flower:
call nla_ok() before nla_next()") only validates the mask pointer
that was just consumed; the pointer produced by nla_next() is used by
the next iteration (fl_set_geneve_opt() and siblings) without any
validation.
The mask's nested attributes are validated with NL_VALIDATE_LIBERAL,
which merely warns on trailing bytes that do not form a complete
attribute. A mask carrying one valid attribute plus 1-3 residue
bytes (or a non-aligned attribute length making msk_depth negative)
therefore reaches the next iteration with msk_depth != 0, so neither
the !msk_depth check in fl_set_enc_opt() nor the !depth check in the
per-type helpers fires. nla_type() then reads past the mask payload
and nla_parse_nested_deprecated() iterates with an nla_len taken
from those bytes, reading well beyond the mask attribute (KASAN:
slab-out-of-bounds read in __nla_validate_parse from fl_change()).
Validate the advanced mask pointer as well: when the mask is not
legitimately exhausted (msk_depth != 0) and the new pointer fails
nla_ok(), reject the filter with -EINVAL. An exactly exhausted mask
still skips the check, preserving exact-match behaviour for the
remaining key attributes. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: fix incorrect MFT record pointer passed to ntfs_attr_record_resize
ntfs_new_attr_flags() passes the wrong MFT record to ntfs_attr_record_resize().
When the attribute is in an extent record, ctx->mrec points to the extent
but the function receives the base record pointer m, causing incorrect
size calculations in memmove.
Fix by passing ctx->mrec (the actual MFT record containing the attribute)
instead of m (the base MFT record) to ntfs_attr_record_resize(). |
| In the Linux kernel, the following vulnerability has been resolved:
x86/CPU/AMD: Fix AMD TLBI Erratum #1718
The processor may fail to invalidate a TLB entry while executing an
INVLPGB/TLBSYNC instruction pair.
Detect the erratum and apply a software workaround when a microcode fix
is not present. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel_pcie: fix TX descriptor bounds check
btintel_pcie_prepare_tx() uses tfd_index to access the TFD and data
buffer arrays before the index is advanced modulo txq->count. An index
equal to txq->count is one past the end of both arrays, so reject it in
the bounds check. |
| The All in One SEO – AI SEO Plugin to Boost SEO Rankings & Traffic (Schema, Local SEO, Sitemap & SEO Insights) plugin for WordPress is vulnerable to Sensitive Information Exposure in all versions up to, and including, 5.0.3 via the 's' parameter. This makes it possible for unauthenticated attackers to extract arbitrary non-public post meta values, including sensitive custom fields such as API keys and internal notes, emitted verbatim into the HTML title element and JSON-LD SearchResultsPage schema. |
| The Newsletters plugin for WordPress is vulnerable to time-based SQL Injection via the 'id' parameter in all versions up to, and including, 4.18.1 due to insufficient escaping on the user supplied parameter and lack of sufficient preparation on the existing SQL query. This makes it possible for authenticated attackers, with subscriber-level access and above, to append additional SQL queries into already existing queries that can be used to extract sensitive information from the database. An attacker can obtain the required nonce and subscriberauth cookie without a WordPress account by simply subscribing through the public newsletter form and opening the management link sent via email; the ownership check verifies only the subscriber_id field and does not validate that the injected id parameter belongs to the authenticated subscriber. |
