| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Add SRCU protection for reading PDPTRs in __get_sregs2()
Add SRCU read-side protection when reading PDPTR registers in
__get_sregs2().
Reading PDPTRs may trigger access to guest memory:
kvm_pdptr_read() -> svm_cache_reg() -> load_pdptrs() ->
kvm_vcpu_read_guest_page() -> kvm_vcpu_gfn_to_memslot()
kvm_vcpu_gfn_to_memslot() dereferences memslots via __kvm_memslots(),
which uses srcu_dereference_check() and requires either kvm->srcu or
kvm->slots_lock to be held. Currently only vcpu->mutex is held,
triggering lockdep warning:
=============================
WARNING: suspicious RCU usage in kvm_vcpu_gfn_to_memslot
6.12.59+ #3 Not tainted
include/linux/kvm_host.h:1062 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by syz.5.1717/15100:
#0: ff1100002f4b00b0 (&vcpu->mutex){+.+.}-{3:3}, at: kvm_vcpu_ioctl+0x1d5/0x1590
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0xf0/0x120 lib/dump_stack.c:120
lockdep_rcu_suspicious+0x1e3/0x270 kernel/locking/lockdep.c:6824
__kvm_memslots include/linux/kvm_host.h:1062 [inline]
__kvm_memslots include/linux/kvm_host.h:1059 [inline]
kvm_vcpu_memslots include/linux/kvm_host.h:1076 [inline]
kvm_vcpu_gfn_to_memslot+0x518/0x5e0 virt/kvm/kvm_main.c:2617
kvm_vcpu_read_guest_page+0x27/0x50 virt/kvm/kvm_main.c:3302
load_pdptrs+0xff/0x4b0 arch/x86/kvm/x86.c:1065
svm_cache_reg+0x1c9/0x230 arch/x86/kvm/svm/svm.c:1688
kvm_pdptr_read arch/x86/kvm/kvm_cache_regs.h:141 [inline]
__get_sregs2 arch/x86/kvm/x86.c:11784 [inline]
kvm_arch_vcpu_ioctl+0x3e20/0x4aa0 arch/x86/kvm/x86.c:6279
kvm_vcpu_ioctl+0x856/0x1590 virt/kvm/kvm_main.c:4663
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl fs/ioctl.c:893 [inline]
__x64_sys_ioctl+0x18b/0x210 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xbd/0x1d0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: roccat: fix use-after-free in roccat_report_event
roccat_report_event() iterates over the device->readers list without
holding the readers_lock. This allows a concurrent roccat_release() to
remove and free a reader while it's still being accessed, leading to a
use-after-free.
Protect the readers list traversal with the readers_lock mutex. |
| In the Linux kernel, the following vulnerability has been resolved:
eventpoll: defer struct eventpoll free to RCU grace period
In certain situations, ep_free() in eventpoll.c will kfree the epi->ep
eventpoll struct while it still being used by another concurrent thread.
Defer the kfree() to an RCU callback to prevent UAF. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: handle wraparound when searching for blocks for indirect mapped blocks
Commit 4865c768b563 ("ext4: always allocate blocks only from groups
inode can use") restricts what blocks will be allocated for indirect
block based files to block numbers that fit within 32-bit block
numbers.
However, when using a review bot running on the latest Gemini LLM to
check this commit when backporting into an LTS based kernel, it raised
this concern:
If ac->ac_g_ex.fe_group is >= ngroups (for instance, if the goal
group was populated via stream allocation from s_mb_last_groups),
then start will be >= ngroups.
Does this allow allocating blocks beyond the 32-bit limit for
indirect block mapped files? The commit message mentions that
ext4_mb_scan_groups_linear() takes care to not select unsupported
groups. However, its loop uses group = *start, and the very first
iteration will call ext4_mb_scan_group() with this unsupported
group because next_linear_group() is only called at the end of the
iteration.
After reviewing the code paths involved and considering the LLM
review, I determined that this can happen when there is a file system
where some files/directories are extent-mapped and others are
indirect-block mapped. To address this, add a safety clamp in
ext4_mb_scan_groups(). |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: don't irele after failing to iget in xfs_attri_recover_work
xlog_recovery_iget* never set @ip to a valid pointer if they return
an error, so this irele will walk off a dangling pointer. Fix that. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_ct: drop pending enqueued packets on removal
Packets sitting in nfqueue might hold a reference to:
- templates that specify the conntrack zone, because a percpu area is
used and module removal is possible.
- conntrack timeout policies and helper, where object removal leave
a stale reference.
Since these objects can just go away, drop enqueued packets to avoid
stale reference to them.
If there is a need for finer grain removal, this logic can be revisited
to make selective packet drop upon dependencies. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: file: Use kzalloc_flex for aio_cmd
The target_core_file doesn't initialize the aio_cmd->iocb for the
ki_write_stream. When a write command fd_execute_rw_aio() is executed,
we may get a bogus ki_write_stream value, causing unintended write
failure status when checking iocb->ki_write_stream > max_write_streams
in the block device.
Let's just use kzalloc_flex when allocating the aio_cmd and let
ki_write_stream=0 to fix this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_conn: fix potential UAF in set_cig_params_sync
hci_conn lookup and field access must be covered by hdev lock in
set_cig_params_sync, otherwise it's possible it is freed concurrently.
Take hdev lock to prevent hci_conn from being deleted or modified
concurrently. Just RCU lock is not suitable here, as we also want to
avoid "tearing" in the configuration. |
| In the Linux kernel, the following vulnerability has been resolved:
thermal: core: Address thermal zone removal races with resume
Since thermal_zone_pm_complete() and thermal_zone_device_resume()
re-initialize the poll_queue delayed work for the given thermal zone,
the cancel_delayed_work_sync() in thermal_zone_device_unregister()
may miss some already running work items and the thermal zone may
be freed prematurely [1].
There are two failing scenarios that both start with
running thermal_pm_notify_complete() right before invoking
thermal_zone_device_unregister() for one of the thermal zones.
In the first scenario, there is a work item already running for
the given thermal zone when thermal_pm_notify_complete() calls
thermal_zone_pm_complete() for that thermal zone and it continues to
run when thermal_zone_device_unregister() starts. Since the poll_queue
delayed work has been re-initialized by thermal_pm_notify_complete(), the
running work item will be missed by the cancel_delayed_work_sync() in
thermal_zone_device_unregister() and if it continues to run past the
freeing of the thermal zone object, a use-after-free will occur.
In the second scenario, thermal_zone_device_resume() queued up by
thermal_pm_notify_complete() runs right after the thermal_zone_exit()
called by thermal_zone_device_unregister() has returned. The poll_queue
delayed work is re-initialized by it before cancel_delayed_work_sync() is
called by thermal_zone_device_unregister(), so it may continue to run
after the freeing of the thermal zone object, which also leads to a
use-after-free.
Address the first failing scenario by ensuring that no thermal work
items will be running when thermal_pm_notify_complete() is called.
For this purpose, first move the cancel_delayed_work() call from
thermal_zone_pm_complete() to thermal_zone_pm_prepare() to prevent
new work from entering the workqueue going forward. Next, switch
over to using a dedicated workqueue for thermal events and update
the code in thermal_pm_notify() to flush that workqueue after
thermal_pm_notify_prepare() has returned which will take care of
all leftover thermal work already on the workqueue (that leftover
work would do nothing useful anyway because all of the thermal zones
have been flagged as suspended).
The second failing scenario is addressed by adding a tz->state check
to thermal_zone_device_resume() to prevent it from re-initializing
the poll_queue delayed work if the thermal zone is going away.
Note that the above changes will also facilitate relocating the suspend
and resume of thermal zones closer to the suspend and resume of devices,
respectively. |
| Use after free in V8 in Google Chrome prior to 155.0.8059.84 allowed a remote attacker to execute arbitrary code inside the sandbox via a crafted HTML page. (Chromium security severity: High) |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipv6: flowlabel: defer exclusive option free until RCU teardown
`ip6fl_seq_show()` walks the global flowlabel hash under the seq-file
RCU read-side lock and prints `fl->opt->opt_nflen` when an option block
is present.
Exclusive flowlabels currently free `fl->opt` as soon as `fl->users`
drops to zero in `fl_release()`. However, the surrounding
`struct ip6_flowlabel` remains visible in the global hash table until
later garbage collection removes it and `fl_free_rcu()` finally tears it
down.
A concurrent `/proc/net/ip6_flowlabel` reader can therefore race that
early `kfree()` and dereference freed option state, triggering a crash
in `ip6fl_seq_show()`.
Fix this by keeping `fl->opt` alive until `fl_free_rcu()`. That matches
the lifetime already required for the enclosing flowlabel while readers
can still reach it under RCU. |
| In the Linux kernel, the following vulnerability has been resolved:
seg6: separate dst_cache for input and output paths in seg6 lwtunnel
The seg6 lwtunnel uses a single dst_cache per encap route, shared
between seg6_input_core() and seg6_output_core(). These two paths
can perform the post-encap SID lookup in different routing contexts
(e.g., ip rules matching on the ingress interface, or VRF table
separation). Whichever path runs first populates the cache, and the
other reuses it blindly, bypassing its own lookup.
Fix this by splitting the cache into cache_input and cache_output,
so each path maintains its own cached dst independently. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: hold claim backbone gateways by reference
batadv_bla_add_claim() can replace claim->backbone_gw and drop the old
gateway's last reference while readers still follow the pointer.
The netlink claim dump path dereferences claim->backbone_gw->orig and
takes claim->backbone_gw->crc_lock without pinning the underlying
backbone gateway. batadv_bla_check_claim() still has the same naked
pointer access pattern.
Reuse batadv_bla_claim_get_backbone_gw() in both readers so they operate
on a stable gateway reference until the read-side work is complete.
This keeps the dump and claim-check paths aligned with the lifetime
rules introduced for the other BLA claim readers. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: smbdirect: introduce smbdirect_socket.recv_io.credits.available
The logic off managing recv credits by counting posted recv_io and
granted credits is racy.
That's because the peer might already consumed a credit,
but between receiving the incoming recv at the hardware
and processing the completion in the 'recv_done' functions
we likely have a window where we grant credits, which
don't really exist.
So we better have a decicated counter for the
available credits, which will be incremented
when we posted new recv buffers and drained when
we grant the credits to the peer. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus/core) Protect regulator operations with mutex
The regulator operations pmbus_regulator_get_voltage(),
pmbus_regulator_set_voltage(), and pmbus_regulator_list_voltage()
access PMBus registers and shared data but were not protected by
the update_lock mutex. This could lead to race conditions.
However, adding mutex protection directly to these functions causes
a deadlock because pmbus_regulator_notify() (which calls
regulator_notifier_call_chain()) is often called with the mutex
already held (e.g., from pmbus_fault_handler()). If a regulator
callback then calls one of the now-protected voltage functions,
it will attempt to acquire the same mutex.
Rework pmbus_regulator_notify() to utilize a worker function to
send notifications outside of the mutex protection. Events are
stored as atomics in a per-page bitmask and processed by the worker.
Initialize the worker and its associated data during regulator
registration, and ensure it is cancelled on device removal using
devm_add_action_or_reset().
While at it, remove the unnecessary include of linux/of.h. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe: always keep track of remap prev/next
During 3D workload, user is reporting hitting:
[ 413.361679] WARNING: drivers/gpu/drm/xe/xe_vm.c:1217 at vm_bind_ioctl_ops_unwind+0x1e2/0x2e0 [xe], CPU#7: vkd3d_queue/9925
[ 413.361944] CPU: 7 UID: 1000 PID: 9925 Comm: vkd3d_queue Kdump: loaded Not tainted 7.0.0-070000rc3-generic #202603090038 PREEMPT(lazy)
[ 413.361949] RIP: 0010:vm_bind_ioctl_ops_unwind+0x1e2/0x2e0 [xe]
[ 413.362074] RSP: 0018:ffffd4c25c3df930 EFLAGS: 00010282
[ 413.362077] RAX: 0000000000000000 RBX: ffff8f3ee817ed10 RCX: 0000000000000000
[ 413.362078] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[ 413.362079] RBP: ffffd4c25c3df980 R08: 0000000000000000 R09: 0000000000000000
[ 413.362081] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8f41fbf99380
[ 413.362082] R13: ffff8f3ee817e968 R14: 00000000ffffffef R15: ffff8f43d00bd380
[ 413.362083] FS: 00000001040ff6c0(0000) GS:ffff8f4696d89000(0000) knlGS:00000000330b0000
[ 413.362085] CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033
[ 413.362086] CR2: 00007ddfc4747000 CR3: 00000002e6262005 CR4: 0000000000f72ef0
[ 413.362088] PKRU: 55555554
[ 413.362089] Call Trace:
[ 413.362092] <TASK>
[ 413.362096] xe_vm_bind_ioctl+0xa9a/0xc60 [xe]
Which seems to hint that the vma we are re-inserting for the ops unwind
is either invalid or overlapping with something already inserted in the
vm. It shouldn't be invalid since this is a re-insertion, so must have
worked before. Leaving the likely culprit as something already placed
where we want to insert the vma.
Following from that, for the case where we do something like a rebind in
the middle of a vma, and one or both mapped ends are already compatible,
we skip doing the rebind of those vma and set next/prev to NULL. As well
as then adjust the original unmap va range, to avoid unmapping the ends.
However, if we trigger the unwind path, we end up with three va, with
the two ends never being removed and the original va range in the middle
still being the shrunken size.
If this occurs, one failure mode is when another unwind op needs to
interact with that range, which can happen with a vector of binds. For
example, if we need to re-insert something in place of the original va.
In this case the va is still the shrunken version, so when removing it
and then doing a re-insert it can overlap with the ends, which were
never removed, triggering a warning like above, plus leaving the vm in a
bad state.
With that, we need two things here:
1) Stop nuking the prev/next tracking for the skip cases. Instead
relying on checking for skip prev/next, where needed. That way on the
unwind path, we now correctly remove both ends.
2) Undo the unmap va shrinkage, on the unwind path. With the two ends
now removed the unmap va should expand back to the original size again,
before re-insertion.
v2:
- Update the explanation in the commit message, based on an actual IGT of
triggering this issue, rather than conjecture.
- Also undo the unmap shrinkage, for the skip case. With the two ends
now removed, the original unmap va range should expand back to the
original range.
v3:
- Track the old start/range separately. vma_size/start() uses the va
info directly.
(cherry picked from commit aec6969f75afbf4e01fd5fb5850ed3e9c27043ac) |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: avoid dereferencing log items after push callbacks
After xfsaild_push_item() calls iop_push(), the log item may have been
freed if the AIL lock was dropped during the push. Background inode
reclaim or the dquot shrinker can free the log item while the AIL lock
is not held, and the tracepoints in the switch statement dereference
the log item after iop_push() returns.
Fix this by capturing the log item type, flags, and LSN before calling
xfsaild_push_item(), and introducing a new xfs_ail_push_class trace
event class that takes these pre-captured values and the ailp pointer
instead of the log item pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: Fix possible invalid memory access after FLR
In the case that the first Function Level Reset (FLR) concludes
correctly, but in the second FLR the scratch area for the saved
configuration cannot be allocated, it's possible for a invalid memory
access to happen.
Always set the deallocated scratch area to NULL after FLR completes. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix read abandonment during retry
Under certain circumstances, all the remaining subrequests from a read
request will get abandoned during retry. The abandonment process expects
the 'subreq' variable to be set to the place to start abandonment from, but
it doesn't always have a useful value (it will be uninitialised on the
first pass through the loop and it may point to a deleted subrequest on
later passes).
Fix the first jump to "abandon:" to set subreq to the start of the first
subrequest expected to need retry (which, in this abandonment case, turned
out unexpectedly to no longer have NEED_RETRY set).
Also clear the subreq pointer after discarding superfluous retryable
subrequests to cause an oops if we do try to access it. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: Hold net reference for the lifetime of /proc/fs/nfs/exports fd
The /proc/fs/nfs/exports proc entry is created at module init
and persists for the module's lifetime. exports_proc_open()
captures the caller's current network namespace and stores
its svc_export_cache in seq->private, but takes no reference
on the namespace. If the namespace is subsequently torn down
(e.g. container destruction after the opener does setns() to a
different namespace), nfsd_net_exit() calls nfsd_export_shutdown()
which frees the cache. Subsequent reads on the still-open fd
dereference the freed cache_detail, walking a freed hash table.
Hold a reference on the struct net for the lifetime of the open
file descriptor. This prevents nfsd_net_exit() from running --
and thus prevents nfsd_export_shutdown() from freeing the cache
-- while any exports fd is open. cache_detail already stores
its net pointer (cd->net, set by cache_create_net()), so
exports_release() can retrieve it without additional per-file
storage. |
