| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
rcu: Fix __this_cpu_read() lockdep warning in rcu_force_quiescent_state()
Running rcutorture with non-zero fqs_duration module parameter in a
kernel built with CONFIG_PREEMPTION=y results in the following splat:
BUG: using __this_cpu_read() in preemptible [00000000]
code: rcu_torture_fqs/398
caller is __this_cpu_preempt_check+0x13/0x20
CPU: 3 PID: 398 Comm: rcu_torture_fqs Not tainted 6.0.0-rc1-yoctodev-standard+
Call Trace:
<TASK>
dump_stack_lvl+0x5b/0x86
dump_stack+0x10/0x16
check_preemption_disabled+0xe5/0xf0
__this_cpu_preempt_check+0x13/0x20
rcu_force_quiescent_state.part.0+0x1c/0x170
rcu_force_quiescent_state+0x1e/0x30
rcu_torture_fqs+0xca/0x160
? rcu_torture_boost+0x430/0x430
kthread+0x192/0x1d0
? kthread_complete_and_exit+0x30/0x30
ret_from_fork+0x22/0x30
</TASK>
The problem is that rcu_force_quiescent_state() uses __this_cpu_read()
in preemptible code instead of the proper raw_cpu_read(). This commit
therefore changes __this_cpu_read() to raw_cpu_read(). |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix bug_on in __es_tree_search caused by bad quota inode
We got a issue as fllows:
==================================================================
kernel BUG at fs/ext4/extents_status.c:202!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 1 PID: 810 Comm: mount Not tainted 6.1.0-rc1-next-g9631525255e3 #352
RIP: 0010:__es_tree_search.isra.0+0xb8/0xe0
RSP: 0018:ffffc90001227900 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 0000000077512a0f RCX: 0000000000000000
RDX: 0000000000000002 RSI: 0000000000002a10 RDI: ffff8881004cd0c8
RBP: ffff888177512ac8 R08: 47ffffffffffffff R09: 0000000000000001
R10: 0000000000000001 R11: 00000000000679af R12: 0000000000002a10
R13: ffff888177512d88 R14: 0000000077512a10 R15: 0000000000000000
FS: 00007f4bd76dbc40(0000)GS:ffff88842fd00000(0000)knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005653bf993cf8 CR3: 000000017bfdf000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
ext4_es_cache_extent+0xe2/0x210
ext4_cache_extents+0xd2/0x110
ext4_find_extent+0x5d5/0x8c0
ext4_ext_map_blocks+0x9c/0x1d30
ext4_map_blocks+0x431/0xa50
ext4_getblk+0x82/0x340
ext4_bread+0x14/0x110
ext4_quota_read+0xf0/0x180
v2_read_header+0x24/0x90
v2_check_quota_file+0x2f/0xa0
dquot_load_quota_sb+0x26c/0x760
dquot_load_quota_inode+0xa5/0x190
ext4_enable_quotas+0x14c/0x300
__ext4_fill_super+0x31cc/0x32c0
ext4_fill_super+0x115/0x2d0
get_tree_bdev+0x1d2/0x360
ext4_get_tree+0x19/0x30
vfs_get_tree+0x26/0xe0
path_mount+0x81d/0xfc0
do_mount+0x8d/0xc0
__x64_sys_mount+0xc0/0x160
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
==================================================================
Above issue may happen as follows:
-------------------------------------
ext4_fill_super
ext4_orphan_cleanup
ext4_enable_quotas
ext4_quota_enable
ext4_iget --> get error inode <5>
ext4_ext_check_inode --> Wrong imode makes it escape inspection
make_bad_inode(inode) --> EXT4_BOOT_LOADER_INO set imode
dquot_load_quota_inode
vfs_setup_quota_inode --> check pass
dquot_load_quota_sb
v2_check_quota_file
v2_read_header
ext4_quota_read
ext4_bread
ext4_getblk
ext4_map_blocks
ext4_ext_map_blocks
ext4_find_extent
ext4_cache_extents
ext4_es_cache_extent
__es_tree_search.isra.0
ext4_es_end --> Wrong extents trigger BUG_ON
In the above issue, s_usr_quota_inum is set to 5, but inode<5> contains
incorrect imode and disordered extents. Because 5 is EXT4_BOOT_LOADER_INO,
the ext4_ext_check_inode check in the ext4_iget function can be bypassed,
finally, the extents that are not checked trigger the BUG_ON in the
__es_tree_search function. To solve this issue, check whether the inode is
bad_inode in vfs_setup_quota_inode(). |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: use proper req destructor for IPv6
Before, only the destructor from TCP request sock in IPv4 was called
even if the subflow was IPv6.
It is important to use the right destructor to avoid memory leaks with
some advanced IPv6 features, e.g. when the request socks contain
specific IPv6 options. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: cdns3: gadget: Use-after-free during failed initialization and exit of cdnsp gadget
In the __cdnsp_gadget_init() and cdnsp_gadget_exit() functions, the gadget
structure (pdev->gadget) was freed before its endpoints.
The endpoints are linked via the ep_list in the gadget structure.
Freeing the gadget first leaves dangling pointers in the endpoint list.
When the endpoints are subsequently freed, this results in a use-after-free.
Fix:
By separating the usb_del_gadget_udc() operation into distinct "del" and
"put" steps, cdnsp_gadget_free_endpoints() can be executed prior to the
final release of the gadget structure with usb_put_gadget().
A patch similar to bb9c74a5bd14("usb: dwc3: gadget: Free gadget structure
only after freeing endpoints"). |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: bcsp: receive data only if registered
Currently, bcsp_recv() can be called even when the BCSP protocol has not
been registered. This leads to a NULL pointer dereference, as shown in
the following stack trace:
KASAN: null-ptr-deref in range [0x0000000000000108-0x000000000000010f]
RIP: 0010:bcsp_recv+0x13d/0x1740 drivers/bluetooth/hci_bcsp.c:590
Call Trace:
<TASK>
hci_uart_tty_receive+0x194/0x220 drivers/bluetooth/hci_ldisc.c:627
tiocsti+0x23c/0x2c0 drivers/tty/tty_io.c:2290
tty_ioctl+0x626/0xde0 drivers/tty/tty_io.c:2706
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
To prevent this, ensure that the HCI_UART_REGISTERED flag is set before
processing received data. If the protocol is not registered, return
-EUNATCH. |
| In the Linux kernel, the following vulnerability has been resolved:
irqchip/mchp-eic: Fix error code in mchp_eic_domain_alloc()
If irq_domain_translate_twocell() sets "hwirq" to >= MCHP_EIC_NIRQ (2) then
it results in an out of bounds access.
The code checks for invalid values, but doesn't set the error code. Return
-EINVAL in that case, instead of returning success. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Free special fields when update [lru_,]percpu_hash maps
As [lru_,]percpu_hash maps support BPF_KPTR_{REF,PERCPU}, missing
calls to 'bpf_obj_free_fields()' in 'pcpu_copy_value()' could cause the
memory referenced by BPF_KPTR_{REF,PERCPU} fields to be held until the
map gets freed.
Fix this by calling 'bpf_obj_free_fields()' after
'copy_map_value[,_long]()' in 'pcpu_copy_value()'. |
| In the Linux kernel, the following vulnerability has been resolved:
gpu: host1x: Fix race in syncpt alloc/free
Fix race condition between host1x_syncpt_alloc()
and host1x_syncpt_put() by using kref_put_mutex()
instead of kref_put() + manual mutex locking.
This ensures no thread can acquire the
syncpt_mutex after the refcount drops to zero
but before syncpt_release acquires it.
This prevents races where syncpoints could
be allocated while still being cleaned up
from a previous release.
Remove explicit mutex locking in syncpt_release
as kref_put_mutex() handles this atomically. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: amba-pl011: avoid SBSA UART accessing DMACR register
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083 b901f001 794038a0 8b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
[1] https://developer.arm.com/documentation/den0094/c/?lang=en
[2] https://lists.xenproject.org/archives/html/xen-devel/2022-11/msg00543.html |
| In the Linux kernel, the following vulnerability has been resolved:
drivers: perf: marvell_cn10k: Fix hotplug callback leak in tad_pmu_init()
tad_pmu_init() won't remove the callback added by cpuhp_setup_state_multi()
when platform_driver_register() failed. Remove the callback by
cpuhp_remove_multi_state() in fail path.
Similar to the handling of arm_ccn_init() in commit 26242b330093 ("bus:
arm-ccn: Prevent hotplug callback leak") |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix missing unmap if z_erofs_get_extent_compressedlen() fails
Otherwise, meta buffers could be leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix potential memory leak in ext4_fc_record_modified_inode()
As krealloc may return NULL, in this case 'state->fc_modified_inodes'
may not be freed by krealloc, but 'state->fc_modified_inodes' already
set NULL. Then will lead to 'state->fc_modified_inodes' memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
NFS: Check the TLS certificate fields in nfs_match_client()
If the TLS security policy is of type RPC_XPRTSEC_TLS_X509, then the
cert_serial and privkey_serial fields need to match as well since they
define the client's identity, as presented to the server. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix memory leak in kfd_mem_dmamap_userptr()
If the number of pages from the userptr BO differs from the SG BO then the
allocated memory for the SG table doesn't get freed before returning
-EINVAL, which may lead to a memory leak in some error paths. Fix this by
checking the number of pages before allocating memory for the SG table. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix monitor mode bringup crash
When the interface is brought up in monitor mode, it leads
to NULL pointer dereference crash. This crash happens when
the packet type is extracted for a SKB. This extraction
which is present in the received msdu delivery path,is
not needed for the monitor ring packets since they are
all RAW packets. Hence appending the flags with
"RX_FLAG_ONLY_MONITOR" to skip that extraction.
Observed calltrace:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000064
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=0000000048517000
[0000000000000064] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
Modules linked in: ath11k_pci ath11k qmi_helpers
CPU: 2 PID: 1781 Comm: napi/-271 Not tainted
6.1.0-rc5-wt-ath-656295-gef907406320c-dirty #6
Hardware name: Qualcomm Technologies, Inc. IPQ8074/AP-HK10-C2 (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k]
lr : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x5c/0x60 [ath11k]
sp : ffff80000ef5bb10
x29: ffff80000ef5bb10 x28: 0000000000000000 x27: ffff000007baafa0
x26: ffff000014a91ed0 x25: 0000000000000000 x24: 0000000000000000
x23: ffff800002b77378 x22: ffff000014a91ec0 x21: ffff000006c8d600
x20: 0000000000000000 x19: ffff800002b77740 x18: 0000000000000006
x17: 736564203634343a x16: 656e694c20657079 x15: 0000000000000143
x14: 00000000ffffffea x13: ffff80000ef5b8b8 x12: ffff80000ef5b8c8
x11: ffff80000a591d30 x10: ffff80000a579d40 x9 : c0000000ffffefff
x8 : 0000000000000003 x7 : 0000000000017fe8 x6 : ffff80000a579ce8
x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 3a35ec12ed7f8900 x1 : 0000000000000000 x0 : 0000000000000052
Call trace:
ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k]
ath11k_dp_rx_deliver_msdu.isra.42+0xa4/0x3d0 [ath11k]
ath11k_dp_rx_mon_deliver.isra.43+0x2f8/0x458 [ath11k]
ath11k_dp_rx_process_mon_rings+0x310/0x4c0 [ath11k]
ath11k_dp_service_srng+0x234/0x338 [ath11k]
ath11k_pcic_ext_grp_napi_poll+0x30/0xb8 [ath11k]
__napi_poll+0x5c/0x190
napi_threaded_poll+0xf0/0x118
kthread+0xf4/0x110
ret_from_fork+0x10/0x20
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
blk-throttle: prevent overflow while calculating wait time
There is a problem found by code review in tg_with_in_bps_limit() that
'bps_limit * jiffy_elapsed_rnd' might overflow. Fix the problem by
calling mul_u64_u64_div_u64() instead. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gud: Fix UBSAN warning
UBSAN complains about invalid value for bool:
[ 101.165172] [drm] Initialized gud 1.0.0 20200422 for 2-3.2:1.0 on minor 1
[ 101.213360] gud 2-3.2:1.0: [drm] fb1: guddrmfb frame buffer device
[ 101.213426] usbcore: registered new interface driver gud
[ 101.989431] ================================================================================
[ 101.989441] UBSAN: invalid-load in linux/include/linux/iosys-map.h:253:9
[ 101.989447] load of value 121 is not a valid value for type '_Bool'
[ 101.989451] CPU: 1 PID: 455 Comm: kworker/1:6 Not tainted 5.18.0-rc5-gud-5.18-rc5 #3
[ 101.989456] Hardware name: Hewlett-Packard HP EliteBook 820 G1/1991, BIOS L71 Ver. 01.44 04/12/2018
[ 101.989459] Workqueue: events_long gud_flush_work [gud]
[ 101.989471] Call Trace:
[ 101.989474] <TASK>
[ 101.989479] dump_stack_lvl+0x49/0x5f
[ 101.989488] dump_stack+0x10/0x12
[ 101.989493] ubsan_epilogue+0x9/0x3b
[ 101.989498] __ubsan_handle_load_invalid_value.cold+0x44/0x49
[ 101.989504] dma_buf_vmap.cold+0x38/0x3d
[ 101.989511] ? find_busiest_group+0x48/0x300
[ 101.989520] drm_gem_shmem_vmap+0x76/0x1b0 [drm_shmem_helper]
[ 101.989528] drm_gem_shmem_object_vmap+0x9/0xb [drm_shmem_helper]
[ 101.989535] drm_gem_vmap+0x26/0x60 [drm]
[ 101.989594] drm_gem_fb_vmap+0x47/0x150 [drm_kms_helper]
[ 101.989630] gud_prep_flush+0xc1/0x710 [gud]
[ 101.989639] ? _raw_spin_lock+0x17/0x40
[ 101.989648] gud_flush_work+0x1e0/0x430 [gud]
[ 101.989653] ? __switch_to+0x11d/0x470
[ 101.989664] process_one_work+0x21f/0x3f0
[ 101.989673] worker_thread+0x200/0x3e0
[ 101.989679] ? rescuer_thread+0x390/0x390
[ 101.989684] kthread+0xfd/0x130
[ 101.989690] ? kthread_complete_and_exit+0x20/0x20
[ 101.989696] ret_from_fork+0x22/0x30
[ 101.989706] </TASK>
[ 101.989708] ================================================================================
The source of this warning is in iosys_map_clear() called from
dma_buf_vmap(). It conditionally sets values based on map->is_iomem. The
iosys_map variables are allocated uninitialized on the stack leading to
->is_iomem having all kinds of values and not only 0/1.
Fix this by zeroing the iosys_map variables. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/hns: Fix refcount leak in hns_roce_mmap
rdma_user_mmap_entry_get_pgoff() takes the reference.
Add missing rdma_user_mmap_entry_put() to release the reference.
Acked-by Haoyue Xu <xuhaoyue1@hisilicon.com> |
| In the Linux kernel, the following vulnerability has been resolved:
bus: fsl-mc: Check return value of platform_get_resource()
platform_get_resource() returns NULL in case of failure, so check its
return value and propagate the error in order to prevent NULL pointer
dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: bmc150: Fix irq assumption regression
The code in bmc150-accel-core.c unconditionally calls
bmc150_accel_set_interrupt() in the iio_buffer_setup_ops,
such as on the runtime PM resume path giving a kernel
splat like this if the device has no interrupts:
Unable to handle kernel NULL pointer dereference at virtual
address 00000001 when read
PC is at bmc150_accel_set_interrupt+0x98/0x194
LR is at __pm_runtime_resume+0x5c/0x64
(...)
Call trace:
bmc150_accel_set_interrupt from bmc150_accel_buffer_postenable+0x40/0x108
bmc150_accel_buffer_postenable from __iio_update_buffers+0xbe0/0xcbc
__iio_update_buffers from enable_store+0x84/0xc8
enable_store from kernfs_fop_write_iter+0x154/0x1b4
This bug seems to have been in the driver since the beginning,
but it only manifests recently, I do not know why.
Store the IRQ number in the state struct, as this is a common
pattern in other drivers, then use this to determine if we have
IRQ support or not. |
